Monday, October 3, 2011

Frigidaire Gas dryer not heating?

HELP ME, MY GAS DRYER IS NOT HEATING?

If your gas dryer is not working because it is not heating then you need to check this out.
Today’s gas dryers often do not use the simple thermocouple with a pilot to prove the flame anymore. They use a much more complicated method of lighting the burner and proving the flame.


HOW DOES THIS GAS DRYER WORKS?
The use of electric igniters has become the standard for many dryers today. The thermostat calls for heat, power is supplied to the igniter, then after a certainamperage draw on the igniter, the gas valve is energizes to open and allow gas to flow starting the flame. As long as the amperage draw on the igniter is high enough then the gas valve stays open till the thermostat is satisfied.


I SEE SOME SPARK COMING FROM IGNITER ?

Sometimes the igniter will crack and no current will go through and the igniter will not even heat up or glow. Sometimes the igniter will wear to the point where it will still heat up and glow, but the current draw will not be high enough to allow the gas valve to open. This creates a confusing situation where you look into the dryer and see the glow from the igniter, but get no heat because the burner never lights up. If this is the case then you will need to replace the igniter even though it seems to be okay. The only way to know for sure is to know what the current draw requirements are for that gas valve and to have an amp meter to check the current draw.


WHAT PART MAJORLY FAILS?

Most of the time the problem will be in the igniter, and not the gas valve. Gas valves can go bad, but that is the case in only a very small amount of the situations. It is a pretty safe bet that if you have a problem with you gas dryer lighting that you have a problem with your igniter.

--------------------

------

FROM WHERE TO GET PARTS IF REQUIRED:----

Replacement parts can be purchased at any of the following web sites:

searspartsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

-------------------------


ANY SAFETY TIP:--

Make sure that you unplug the dryer before checking any of the heating components.For information as to where the different components are you can do a search for “appliance parts” and then enter you model number in one of the parts supply web sites.

BASIC HOUSEHOLD TOOLS LIKE SCREWDRIVER, PLIERS, PRIER, AND PUTTY KNIFE ETC ETC ARE REQUIRED. -----

ALWAYS KEEP MARKER AND HANDY-CAM READY, WHILE PERFORMING THESE JOBS.

MARKER COMES IN USE TO MARK THE POSITION OR PARTICULAR WIRE OR SCREW AND HANDY CAM COMES IN USE FOR GETTING THE EXACT PICTURE OF PART,WHEN IT WAS ASSEMBLED, SO WHILE DIS-ASSEMBLY, YOU CAN JUST VIEW THE PICTURE/PHOTO AND THAT HELPS YOU A LOT.


--------------------

FOR MORE DRYER RELATED PROBLEM TROUBLESHOOTING AND HELP:---

How to replace electronic control board onKitchen Range?

http://washingmachineforum.blogspot.com/2011/09/how-to-replace-electronic-control-board.html

How to replace the heating element on dryer?

http://schematicsdiagram.blogspot.com/2011/09/how-to-replace-heating-element-on-dryer.html

HOW TO REPLACE DRIVE BELT ON DRYER?

http://washingmachineforum.blogspot.com/2011/09/how-to-replace-drive-belt-on-dryer.html

Electric dryer not heating?

http://dryerhelp.blogspot.com/2011/10/electric-dryer-not-heating.html

Gas dryer not heating?

http://dryerhelp.blogspot.com/2011/10/gas-dryer-not-heating.html

Dryer will not heat?

http://dryerhelp.blogspot.com/2011/10/dryer-will-not-heat.html

Dryer not turning?

http://dryerhelp.blogspot.com/2011/10/dryer-not-turning.html

Dryer will not start?

http://dryerhelp.blogspot.com/2011/10/dryer-will-not-start.html


No comments:

Post a Comment